NAME


terminfo - terminal capability data base

SYNOPSIS


/usr/share/terminfo/*/*

DESCRIPTION


Terminfo is a data base describing terminals, used by screen-oriented programs such as nvi(1), rogue(1) and libraries such as ncurses(3NCURSES). Terminfo describes terminals by giving a set of capabilities which they have, by specifying how to perform screen operations, and by specifying padding requirements and initialization sequences. This describes ncurses version 5.6 (patch 20080804).

Entries in terminfo consist of a sequence of ‘,’ separated fields (embedded commas may be escaped with a backslash or notated as \054). White space after the ‘,’ separator is ignored. The first entry for each terminal gives the names which are known for the terminal, separated by ‘|’ characters. The first name given is the most common abbreviation for the terminal, the last name given should be a long name fully identifying the terminal, and all others are understood as synonyms for the terminal name. All names but the last should be in lower case and contain no blanks; the last name may well contain upper case and blanks for readability.

Lines beginning with a ‘#’ in the first column are treated as comments. While comment lines are legal at any point, the output of captoinfo and infotocap (aliases for tic) will move comments so they occur only between entries.

Newlines and leading tabs may be used for formatting entries for readability. These are removed from parsed entries. The infocmp -f option relies on this to format if-then-else expressions: the result can be read by tic.

Terminal names (except for the last, verbose entry) should be chosen using the following conventions. The particular piece of hardware making up the terminal should have a root name, thus ‘‘hp2621’’. This name should not contain hyphens. Modes that the hardware can be in, or user preferences, should be indicated by appending a hyphen and a mode suffix. Thus, a vt100 in 132 column mode would be vt100-w. The following suffixes should be used where possible:

SuffixMeaningExample
-nnNumber of lines on the screenaaa-60
-npNumber of pages of memoryc100-4p
-amWith automargins (usually the default)vt100-am
-mMono mode; suppress coloransi-m
-mcMagic cookie; spaces when highlightingwy30-mc
-naNo arrow keys (leave them in local)c100-na
-namWithout automatic marginsvt100-nam
-nlNo status lineatt4415-nl
-nsNo status linehp2626-ns
-rvReverse videoc100-rv
-sEnable status linevt100-s
-vbUse visible bell instead of beepwy370-vb
-wWide mode (> 80 columns, usually 132)vt100-w

For more on terminal naming conventions, see the term(7) manual page.

Capabilities

The following is a complete table of the capabilities included in a terminfo description block and available to terminfo-using code. In each line of the table,

The variable is the name by which the programmer (at the terminfo level) accesses the capability.

The capname is the short name used in the text of the database, and is used by a person updating the database. Whenever possible, capnames are chosen to be the same as or similar to the ANSI X3.64-1979 standard (now superseded by ECMA-48, which uses identical or very similar names). Semantics are also intended to match those of the specification.

The termcap code is the old termcap capability name (some capabilities are new, and have names which termcap did not originate).

Capability names have no hard length limit, but an informal limit of 5 characters has been adopted to keep them short and to allow the tabs in the source file Caps to line up nicely.

Finally, the description field attempts to convey the semantics of the capability. You may find some codes in the description field:
(P) indicates that padding may be specified
#[1-9] in the description field indicates that the string is passed through tparm with parms as given (#i).
(P*) indicates that padding may vary in proportion to the number of lines affected
(#i) indicates the ith parameter.

These are the boolean capabilities:

VariableCap-TCapDescription
BooleansnameCode 
auto_left_marginbwbwcub1 wraps from column 0 to last column
auto_right_marginamamterminal has automatic margins
back_color_erasebceutscreen erased with background color
can_changecccccterminal can re-define existing colors
ceol_standout_glitchxhpxsstandout not erased by overwriting (hp)
col_addr_glitchxhpaYAonly positive motion for hpa/mhpa caps
cpi_changes_rescpixYFchanging character pitch changes resolution
cr_cancels_micro_modecrxmYBusing cr turns off micro mode
dest_tabs_magic_smsoxtxttabs destructive, magic so char (t1061)
eat_newline_glitchxenlxnnewline ignored after 80 cols (concept)
erase_overstrikeeoeocan erase overstrikes with a blank
generic_typegngngeneric line type
hard_copyhchchardcopy terminal
hard_cursorchtsHCcursor is hard to see
has_meta_keykmkmHas a meta key (i.e., sets 8th-bit)
has_print_wheeldaisyYCprinter needs operator to change character set
has_status_linehshshas extra status line
hue_lightness_saturationhlshlterminal uses only HLS color notation (Tektronix)
insert_null_glitchinininsert mode distinguishes nulls
lpi_changes_reslpixYGchanging line pitch changes resolution
memory_abovedadadisplay may be retained above the screen
memory_belowdbdbdisplay may be retained below the screen
move_insert_modemirmisafe to move while in insert mode
move_standout_modemsgrmssafe to move while in standout mode
needs_xon_xoffnxonnxpadding will not work, xon/xoff required
no_esc_ctlcxsbxbbeehive (f1=escape, f2=ctrl C)
no_pad_charnpcNPpad character does not exist
non_dest_scroll_regionndscrNDscrolling region is non-destructive
non_rev_rmcupnrrmcNRsmcup does not reverse rmcup
over_strikeososterminal can overstrike
prtr_silentmc5i5iprinter will not echo on screen
row_addr_glitchxvpaYDonly positive motion for vpa/mvpa caps
semi_auto_right_marginsamYEprinting in last column causes cr
status_line_esc_okeslokesescape can be used on the status line
tilde_glitchhzhzcannot print ~’s (hazeltine)
transparent_underlineululunderline character overstrikes
xon_xoffxonxoterminal uses xon/xoff handshaking

These are the numeric capabilities:

VariableCap-TCapDescription
NumericnameCode 
columnscolsconumber of columns in a line
init_tabsitittabs initially every # spaces
label_heightlhlhrows in each label
label_widthlwlwcolumns in each label
lineslineslinumber of lines on screen or page
lines_of_memorylmlmlines of memory if > line. 0 means varies
magic_cookie_glitchxmcsgnumber of blank characters left by smso or rmso
max_attributesmamamaximum combined attributes terminal can handle
max_colorscolorsComaximum number of colors on screen
max_pairspairspamaximum number of color-pairs on the screen
maximum_windowswnumMWmaximum number of defineable windows
no_color_videoncvNCvideo attributes that cannot be used with colors
num_labelsnlabNlnumber of labels on screen
padding_baud_ratepbpblowest baud rate where padding needed
virtual_terminalvtvtvirtual terminal number (CB/unix)
width_status_linewslwsnumber of columns in status line

The following numeric capabilities are present in the SVr4.0 term structure, but are not yet documented in the man page. They came in with SVr4’s printer support.

VariableCap-TCapDescription
NumericnameCode 
bit_image_entwiningbitwinYonumber of passes for each bit-image row
bit_image_typebitypeYptype of bit-image device
buffer_capacitybufszYanumbers of bytes buffered before printing
buttonsbtnsBTnumber of buttons on mouse
dot_horz_spacingspinhYcspacing of dots horizontally in dots per inch
dot_vert_spacingspinvYbspacing of pins vertically in pins per inch
max_micro_addressmaddrYdmaximum value in micro_..._address
max_micro_jumpmjumpYemaximum value in parm_..._micro
micro_col_sizemcsYfcharacter step size when in micro mode
micro_line_sizemlsYgline step size when in micro mode
number_of_pinsnpinsYhnumbers of pins in print-head
output_res_charorcYihorizontal resolution in units per line
output_res_horz_inchorhiYkhorizontal resolution in units per inch
output_res_lineorlYjvertical resolution in units per line
output_res_vert_inchorviYlvertical resolution in units per inch
print_ratecpsYmprint rate in characters per second
wide_char_sizewidcsYncharacter step size when in double wide mode

These are the string capabilities:

VariableCap-TCapDescription
StringnameCode 
acs_charsacscacgraphics charset pairs, based on vt100
back_tabcbtbtback tab (P)
bellbelblaudible signal (bell) (P)
carriage_returncrcrcarriage return (P*) (P*)
change_char_pitchcpiZAChange number of characters per inch to #1
change_line_pitchlpiZBChange number of lines per inch to #1
change_res_horzchrZCChange horizontal resolution to #1
change_res_vertcvrZDChange vertical resolution to #1
change_scroll_regioncsrcschange region to line #1 to line #2 (P)
char_paddingrmprPlike ip but when in insert mode
clear_all_tabstbcctclear all tab stops (P)
clear_marginsmgcMCclear right and left soft margins
clear_screenclearclclear screen and home cursor (P*)
clr_bolel1cbClear to beginning of line
clr_eolelceclear to end of line (P)
clr_eosedcdclear to end of screen (P*)
column_addresshpachhorizontal position #1, absolute (P)
command_charactercmdchCCterminal settable cmd character in prototype !?
create_windowcwinCWdefine a window #1 from #2,#3 to #4,#5
cursor_addresscupcmmove to row #1 columns #2
cursor_downcud1dodown one line
cursor_homehomehohome cursor (if no cup)
cursor_invisiblecivisvimake cursor invisible
cursor_leftcub1lemove left one space
cursor_mem_addressmrcupCMmemory relative cursor addressing, move to row #1 columns #2
cursor_normalcnormvemake cursor appear normal (undo civis/cvvis)
cursor_rightcuf1ndnon-destructive space (move right one space)
cursor_to_lllllllast line, first column (if no cup)
cursor_upcuu1upup one line
cursor_visiblecvvisvsmake cursor very visible
define_chardefcZEDefine a character #1, #2 dots wide, descender #3
delete_characterdch1dcdelete character (P*)
delete_linedl1dldelete line (P*)
dial_phonedialDIdial number #1
dis_status_linedsldsdisable status line
display_clockdclkDKdisplay clock
down_half_linehdhdhalf a line down
ena_acsenacseAenable alternate char set
enter_alt_charset_modesmacsasstart alternate character set (P)
enter_am_modesmamSAturn on automatic margins
enter_blink_modeblinkmbturn on blinking
enter_bold_modeboldmdturn on bold (extra bright) mode
enter_ca_modesmcuptistring to start programs using cup
enter_delete_modesmdcdmenter delete mode
enter_dim_modedimmhturn on half-bright mode
enter_doublewide_modeswidmZFEnter double-wide mode
enter_draft_qualitysdrfqZGEnter draft-quality mode
enter_insert_modesmirimenter insert mode
enter_italics_modesitmZHEnter italic mode
enter_leftward_modeslmZIStart leftward carriage motion
enter_micro_modesmicmZJStart micro-motion mode
enter_near_letter_qualitysnlqZKEnter NLQ mode
enter_normal_qualitysnrmqZLEnter normal-quality mode
enter_protected_modeprotmpturn on protected mode
enter_reverse_moderevmrturn on reverse video mode
enter_secure_modeinvismkturn on blank mode (characters invisible)
enter_shadow_modesshmZMEnter shadow-print mode
enter_standout_modesmsosobegin standout mode
enter_subscript_modessubmZNEnter subscript mode
enter_superscript_modessupmZOEnter superscript mode
enter_underline_modesmulusbegin underline mode
enter_upward_modesumZPStart upward carriage motion
enter_xon_modesmxonSXturn on xon/xoff handshaking
erase_charsechecerase #1 characters (P)
exit_alt_charset_modermacsaeend alternate character set (P)
exit_am_modermamRAturn off automatic margins
exit_attribute_modesgr0meturn off all attributes
exit_ca_modermcuptestrings to end programs using cup
exit_delete_modermdcedend delete mode
exit_doublewide_moderwidmZQEnd double-wide mode
exit_insert_modermireiexit insert mode
exit_italics_moderitmZREnd italic mode
exit_leftward_moderlmZSEnd left-motion mode
exit_micro_modermicmZTEnd micro-motion mode
exit_shadow_modershmZUEnd shadow-print mode
exit_standout_modermsoseexit standout mode
exit_subscript_modersubmZVEnd subscript mode
exit_superscript_modersupmZWEnd superscript mode
exit_underline_modermulueexit underline mode
exit_upward_moderumZXEnd reverse character motion
exit_xon_modermxonRXturn off xon/xoff handshaking
fixed_pausepausePApause for 2-3 seconds
flash_hookhookfhflash switch hook
flash_screenflashvbvisible bell (may not move cursor)
form_feedffffhardcopy terminal page eject (P*)
from_status_linefslfsreturn from status line
goto_windowwingoWGgo to window #1
hanguphupHUhang-up phone
init_1stringis1i1initialization string
init_2stringis2isinitialization string
init_3stringis3i3initialization string
init_fileififname of initialization file
init_progiprogiPpath name of program for initialization
initialize_colorinitcIcinitialize color #1 to (#2,#3,#4)
initialize_pairinitpIpInitialize color pair #1 to fg=(#2,#3,#4), bg=(#5,#6,#7)
insert_characterich1icinsert character (P)
insert_lineil1alinsert line (P*)
insert_paddingipipinsert padding after inserted character
key_a1ka1K1upper left of keypad
key_a3ka3K3upper right of keypad
key_b2kb2K2center of keypad
key_backspacekbskbbackspace key
key_begkbeg@1begin key
key_btabkcbtkBback-tab key
key_c1kc1K4lower left of keypad
key_c3kc3K5lower right of keypad
key_cancelkcan@2cancel key
key_catabktbckaclear-all-tabs key
key_clearkclrkCclear-screen or erase key
key_closekclo@3close key
key_commandkcmd@4command key
key_copykcpy@5copy key
key_createkcrt@6create key
key_ctabkctabktclear-tab key
key_dckdch1kDdelete-character key
key_dlkdl1kLdelete-line key
key_downkcud1kddown-arrow key
key_eickrmirkMsent by rmir or smir in insert mode
key_endkend@7end key
key_enterkent@8enter/send key
key_eolkelkEclear-to-end-of-line key
key_eoskedkSclear-to-end-of-screen key
key_exitkext@9exit key
key_f0kf0k0F0 function key
key_f1kf1k1F1 function key
key_f10kf10k;F10 function key
key_f11kf11F1F11 function key
key_f12kf12F2F12 function key
key_f13kf13F3F13 function key
key_f14kf14F4F14 function key
key_f15kf15F5F15 function key
key_f16kf16F6F16 function key
key_f17kf17F7F17 function key
key_f18kf18F8F18 function key
key_f19kf19F9F19 function key
key_f2kf2k2F2 function key
key_f20kf20FAF20 function key
key_f21kf21FBF21 function key
key_f22kf22FCF22 function key
key_f23kf23FDF23 function key
key_f24kf24FEF24 function key
key_f25kf25FFF25 function key
key_f26kf26FGF26 function key
key_f27kf27FHF27 function key
key_f28kf28FIF28 function key
key_f29kf29FJF29 function key
key_f3kf3k3F3 function key
key_f30kf30FKF30 function key
key_f31kf31FLF31 function key
key_f32kf32FMF32 function key
key_f33kf33FNF33 function key
key_f34kf34FOF34 function key
key_f35kf35FPF35 function key
key_f36kf36FQF36 function key
key_f37kf37FRF37 function key
key_f38kf38FSF38 function key
key_f39kf39FTF39 function key
key_f4kf4k4F4 function key
key_f40kf40FUF40 function key
key_f41kf41FVF41 function key
key_f42kf42FWF42 function key
key_f43kf43FXF43 function key
key_f44kf44FYF44 function key
key_f45kf45FZF45 function key
key_f46kf46FaF46 function key
key_f47kf47FbF47 function key
key_f48kf48FcF48 function key
key_f49kf49FdF49 function key
key_f5kf5k5F5 function key
key_f50kf50FeF50 function key
key_f51kf51FfF51 function key
key_f52kf52FgF52 function key
key_f53kf53FhF53 function key
key_f54kf54FiF54 function key
key_f55kf55FjF55 function key
key_f56kf56FkF56 function key
key_f57kf57FlF57 function key
key_f58kf58FmF58 function key
key_f59kf59FnF59 function key
key_f6kf6k6F6 function key
key_f60kf60FoF60 function key
key_f61kf61FpF61 function key
key_f62kf62FqF62 function key
key_f63kf63FrF63 function key
key_f7kf7k7F7 function key
key_f8kf8k8F8 function key
key_f9kf9k9F9 function key
key_findkfnd@0find key
key_helpkhlp%1help key
key_homekhomekhhome key
key_ickich1kIinsert-character key
key_ilkil1kAinsert-line key
key_leftkcub1klleft-arrow key
key_llkllkHlower-left key (home down)
key_markkmrk%2mark key
key_messagekmsg%3message key
key_movekmov%4move key
key_nextknxt%5next key
key_npageknpkNnext-page key
key_openkopn%6open key
key_optionskopt%7options key
key_ppagekppkPprevious-page key
key_previouskprv%8previous key
key_printkprt%9print key
key_redokrdo%0redo key
key_referencekref&1reference key
key_refreshkrfr&2refresh key
key_replacekrpl&3replace key
key_restartkrst&4restart key
key_resumekres&5resume key
key_rightkcuf1krright-arrow key
key_saveksav&6save key
key_sbegkBEG&9shifted begin key
key_scancelkCAN&0shifted cancel key
key_scommandkCMD*1shifted command key
key_scopykCPY*2shifted copy key
key_screatekCRT*3shifted create key
key_sdckDC*4shifted delete-character key
key_sdlkDL*5shifted delete-line key
key_selectkslt*6select key
key_sendkEND*7shifted end key
key_seolkEOL*8shifted clear-to-end-of-line key
key_sexitkEXT*9shifted exit key
key_sfkindkFscroll-forward key
key_sfindkFND*0shifted find key
key_shelpkHLP#1shifted help key
key_shomekHOM#2shifted home key
key_sickIC#3shifted insert-character key
key_sleftkLFT#4shifted left-arrow key
key_smessagekMSG%ashifted message key
key_smovekMOV%bshifted move key
key_snextkNXT%cshifted next key
key_soptionskOPT%dshifted options key
key_spreviouskPRV%eshifted previous key
key_sprintkPRT%fshifted print key
key_srkrikRscroll-backward key
key_sredokRDO%gshifted redo key
key_sreplacekRPL%hshifted replace key
key_srightkRIT%ishifted right-arrow key
key_srsumekRES%jshifted resume key
key_ssavekSAV!1shifted save key
key_ssuspendkSPD!2shifted suspend key
key_stabkhtskTset-tab key
key_sundokUND!3shifted undo key
key_suspendkspd&7suspend key
key_undokund&8undo key
key_upkcuu1kuup-arrow key
keypad_localrmkxkeleave ’keyboard_transmit’ mode
keypad_xmitsmkxksenter ’keyboard_transmit’ mode
lab_f0lf0l0label on function key f0 if not f0
lab_f1lf1l1label on function key f1 if not f1
lab_f10lf10lalabel on function key f10 if not f10
lab_f2lf2l2label on function key f2 if not f2
lab_f3lf3l3label on function key f3 if not f3
lab_f4lf4l4label on function key f4 if not f4
lab_f5lf5l5label on function key f5 if not f5
lab_f6lf6l6label on function key f6 if not f6
lab_f7lf7l7label on function key f7 if not f7
lab_f8lf8l8label on function key f8 if not f8
lab_f9lf9l9label on function key f9 if not f9
label_formatflnLflabel format
label_offrmlnLFturn off soft labels
label_onsmlnLOturn on soft labels
meta_offrmmmoturn off meta mode
meta_onsmmmmturn on meta mode (8th-bit on)
micro_column_addressmhpaZYLike column_address in micro mode
micro_downmcud1ZZLike cursor_down in micro mode
micro_leftmcub1ZaLike cursor_left in micro mode
micro_rightmcuf1ZbLike cursor_right in micro mode
micro_row_addressmvpaZcLike row_address #1 in micro mode
micro_upmcuu1ZdLike cursor_up in micro mode
newlinenelnwnewline (behave like cr followed by lf)
order_of_pinsporderZeMatch software bits to print-head pins
orig_colorsococSet all color pairs to the original ones
orig_pairopopSet default pair to its original value
pad_charpadpcpadding char (instead of null)
parm_dchdchDCdelete #1 characters (P*)
parm_delete_linedlDLdelete #1 lines (P*)
parm_down_cursorcudDOdown #1 lines (P*)
parm_down_micromcudZfLike parm_down_cursor in micro mode
parm_ichichICinsert #1 characters (P*)
parm_indexindnSFscroll forward #1 lines (P)
parm_insert_lineilALinsert #1 lines (P*)
parm_left_cursorcubLEmove #1 characters to the left (P)
parm_left_micromcubZgLike parm_left_cursor in micro mode
parm_right_cursorcufRImove #1 characters to the right (P*)
parm_right_micromcufZhLike parm_right_cursor in micro mode
parm_rindexrinSRscroll back #1 lines (P)
parm_up_cursorcuuUPup #1 lines (P*)
parm_up_micromcuuZiLike parm_up_cursor in micro mode
pkey_keypfkeypkprogram function key #1 to type string #2
pkey_localpflocplprogram function key #1 to execute string #2
pkey_xmitpfxpxprogram function key #1 to transmit string #2
plab_normplnpnprogram label #1 to show string #2
print_screenmc0psprint contents of screen
prtr_nonmc5ppOturn on printer for #1 bytes
prtr_offmc4pfturn off printer
prtr_onmc5poturn on printer
pulsepulsePUselect pulse dialing
quick_dialqdialQDdial number #1 without checking
remove_clockrmclkRCremove clock
repeat_charreprprepeat char #1 #2 times (P*)
req_for_inputrfiRFsend next input char (for ptys)
reset_1stringrs1r1reset string
reset_2stringrs2r2reset string
reset_3stringrs3r3reset string
reset_filerfrfname of reset file
restore_cursorrcrcrestore cursor to position of last save_cursor
row_addressvpacvvertical position #1 absolute (P)
save_cursorscscsave current cursor position (P)
scroll_forwardindsfscroll text up (P)
scroll_reverserisrscroll text down (P)
select_char_setscsZjSelect character set, #1
set_attributessgrsadefine video attributes #1-#9 (PG9)
set_backgroundsetbSbSet background color #1
set_bottom_marginsmgbZkSet bottom margin at current line
set_bottom_margin_parmsmgbpZlSet bottom margin at line #1 or (if smgtp is not given) #2 lines from bottom
set_clocksclkSCset clock, #1 hrs #2 mins #3 secs
set_color_pairscpspSet current color pair to #1
set_foregroundsetfSfSet foreground color #1
set_left_marginsmglMLset left soft margin at current column.  See smgl. (ML is not in BSD termcap).
set_left_margin_parmsmglpZmSet left (right) margin at column #1
set_right_marginsmgrMRset right soft margin at current column
set_right_margin_parmsmgrpZnSet right margin at column #1
set_tabhtsstset a tab in every row, current columns
set_top_marginsmgtZoSet top margin at current line
set_top_margin_parmsmgtpZpSet top (bottom) margin at row #1
set_windowwindwicurrent window is lines #1-#2 cols #3-#4
start_bit_imagesbimZqStart printing bit image graphics
start_char_set_defscsdZrStart character set definition #1, with #2 characters in the set
stop_bit_imagerbimZsStop printing bit image graphics
stop_char_set_defrcsdZtEnd definition of character set #1
subscript_characterssubcsZuList of subscriptable characters
superscript_characterssupcsZvList of superscriptable characters
tabhttatab to next 8-space hardware tab stop
these_cause_crdocrZwPrinting any of these characters causes CR
to_status_linetsltsmove to status line, column #1
tonetoneTOselect touch tone dialing
underline_charucucunderline char and move past it
up_half_linehuhuhalf a line up
user0u0u0User string #0
user1u1u1User string #1
user2u2u2User string #2
user3u3u3User string #3
user4u4u4User string #4
user5u5u5User string #5
user6u6u6User string #6
user7u7u7User string #7
user8u8u8User string #8
user9u9u9User string #9
wait_tonewaitWAwait for dial-tone
xoff_characterxoffcXFXOFF character
xon_characterxoncXNXON character
zero_motionzeromZxNo motion for subsequent character

The following string capabilities are present in the SVr4.0 term structure, but were originally not documented in the man page.

VariableCap-TCapDescription
StringnameCode 
alt_scancode_escscesaS8Alternate escape for scancode emulation
bit_image_carriage_returnbicrYvMove to beginning of same row
bit_image_newlinebinelZzMove to next row of the bit image
bit_image_repeatbirepXyRepeat bit image cell #1 #2 times
char_set_namescsnmZyProduce #1’th item from list of character set names
code_set_initcsinciInit sequence for multiple codesets
color_namescolornmYwGive name for color #1
define_bit_image_regiondefbiYxDefine rectangualar bit image region
device_typedevtdvIndicate language/codeset support
display_pc_chardispcS1Display PC character #1
end_bit_image_regionendbiYyEnd a bit-image region
enter_pc_charset_modesmpchS2Enter PC character display mode
enter_scancode_modesmscS4Enter PC scancode mode
exit_pc_charset_modermpchS3Exit PC character display mode
exit_scancode_modermscS5Exit PC scancode mode
get_mousegetmGmCurses should get button events, parameter #1 not documented.
key_mousekmousKmMouse event has occurred
mouse_infominfoMiMouse status information
pc_term_optionspctrmS6PC terminal options
pkey_plabpfxlxlProgram function key #1 to type string #2 and show string #3
req_mouse_posreqmpRQRequest mouse position
scancode_escapescescS7Escape for scancode emulation
set0_des_seqs0dss0Shift to codeset 0 (EUC set 0, ASCII)
set1_des_seqs1dss1Shift to codeset 1
set2_des_seqs2dss2Shift to codeset 2
set3_des_seqs3dss3Shift to codeset 3
set_a_backgroundsetabABSet background color to #1, using ANSI escape
set_a_foregroundsetafAFSet foreground color to #1, using ANSI escape
set_color_bandsetcolorYzChange to ribbon color #1
set_lr_marginsmglrMLSet both left and right margins to #1, #2. (ML is not in BSD termcap).
set_page_lengthslinesYZSet page length to #1 lines
set_tb_marginsmgtbMTSets both top and bottom margins to #1, #2

The XSI Curses standard added these. They are some post-4.1 versions of System V curses, e.g., Solaris 2.5 and IRIX 6.x. The ncurses termcap names for them are invented; according to the XSI Curses standard, they have no termcap names. If your compiled terminfo entries use these, they may not be binary-compatible with System V terminfo entries after SVr4.1; beware!

VariableCap-TCapDescription
StringnameCode 
enter_horizontal_hl_modeehhlmXhEnter horizontal highlight mode
enter_left_hl_modeelhlmXlEnter left highlight mode
enter_low_hl_modeelohlmXoEnter low highlight mode
enter_right_hl_modeerhlmXrEnter right highlight mode
enter_top_hl_modeethlmXtEnter top highlight mode
enter_vertical_hl_modeevhlmXvEnter vertical highlight mode
set_a_attributessgr1sADefine second set of video attributes #1-#6
set_pglen_inchslengthsLYI Set page length to #1 hundredth of an inch

A Sample Entry

The following entry, describing an ANSI-standard terminal, is representative of what a terminfo entry for a modern terminal typically looks like.

ansi|ansi/pc-term compatible with color,
        mc5i,
        colors#8, ncv#3, pairs#64,
        cub=\E[%p1%dD, cud=\E[%p1%dB, cuf=\E[%p1%dC,
        cuu=\E[%p1%dA, dch=\E[%p1%dP, dl=\E[%p1%dM,
        ech=\E[%p1%dX, el1=\E[1K, hpa=\E[%p1%dG, ht=\E[I,
        ich=\E[%p1%d@, il=\E[%p1%dL, indn=\E[%p1%dS, .indn=\E[%p1%dT,
        kbs=^H, kcbt=\E[Z, kcub1=\E[D, kcud1=\E[B,
        kcuf1=\E[C, kcuu1=\E[A, kf1=\E[M, kf10=\E[V,
        kf11=\E[W, kf12=\E[X, kf2=\E[N, kf3=\E[O, kf4=\E[P,
        kf5=\E[Q, kf6=\E[R, kf7=\E[S, kf8=\E[T, kf9=\E[U,
        kich1=\E[L, mc4=\E[4i, mc5=\E[5i, nel=\r\E[S,
        op=\E[37;40m, rep=%p1%c\E[%p2%{1}%-%db,
        rin=\E[%p1%dT, s0ds=\E(B, s1ds=\E)B, s2ds=\E*B,
        s3ds=\E+B, setab=\E[4%p1%dm, setaf=\E[3%p1%dm,
        setb=\E[4%?%p1%{1}%=%t4%e%p1%{3}%=%t6%e%p1%{4}%=%t1%e%p1%{6}%=%t3%e%p1%d%;m,
        setf=\E[3%?%p1%{1}%=%t4%e%p1%{3}%=%t6%e%p1%{4}%=%t1%e%p1%{6}%=%t3%e%p1%d%;m,
        sgr=\E[0;10%?%p1%t;7%;%?%p2%t;4%;%?%p3%t;7%;%?%p4%t;5%;%?%p6%t;1%;%?%p7%t;8%;%?%p8%t;11%;%?%p9%t;12%;m,
        sgr0=\E[0;10m, tbc=\E[2g, u6=\E[%d;%dR, u7=\E[6n,
        u8=\E[?%[;0123456789]c, u9=\E[c, vpa=\E[%p1%dd,

Entries may continue onto multiple lines by placing white space at the beginning of each line except the first. Comments may be included on lines beginning with ‘‘#’’. Capabilities in terminfo are of three types: Boolean capabilities which indicate that the terminal has some particular feature, numeric capabilities giving the size of the terminal or the size of particular delays, and string capabilities, which give a sequence which can be used to perform particular terminal operations.

Types of Capabilities

All capabilities have names. For instance, the fact that ANSI-standard terminals have automatic margins (i.e., an automatic return and line-feed when the end of a line is reached) is indicated by the capability am. Hence the description of ansi includes am. Numeric capabilities are followed by the character ‘#’ and then a positive value. Thus cols, which indicates the number of columns the terminal has, gives the value ‘80’ for ansi. Values for numeric capabilities may be specified in decimal, octal or hexadecimal, using the C programming language conventions (e.g., 255, 0377 and 0xff or 0xFF).

Finally, string valued capabilities, such as el (clear to end of line sequence) are given by the two-character code, an ‘=’, and then a string ending at the next following ‘,’.

A number of escape sequences are provided in the string valued capabilities for easy encoding of characters there. Both \E and \e map to an ESCAPE character, ^x maps to a control-x for any appropriate x, and the sequences \n \l \r \t \b \f \s give a newline, line-feed, return, tab, backspace, form-feed, and space. Other escapes include \^ for ^, \\ for \, \, for comma, \: for :, and \0 for null. (\0 will produce \200, which does not terminate a string but behaves as a null character on most terminals, providing CS7 is specified. See stty(1).) Finally, characters may be given as three octal digits after a \.

A delay in milliseconds may appear anywhere in a string capability, enclosed in $<..> brackets, as in el=\EK$<5>, and padding characters are supplied by tputs to provide this delay. The delay must be a number with at most one decimal place of precision; it may be followed by suffixes ‘*’ or ’/’ or both. A ‘*’ indicates that the padding required is proportional to the number of lines affected by the operation, and the amount given is the per-affected-unit padding required. (In the case of insert character, the factor is still the number of lines affected.) Normally, padding is advisory if the device has the xon capability; it is used for cost computation but does not trigger delays. A ‘/’ suffix indicates that the padding is mandatory and forces a delay of the given number of milliseconds even on devices for which xon is present to indicate flow control.

Sometimes individual capabilities must be commented out. To do this, put a period before the capability name. For example, see the second ind in the example above.

Fetching Compiled Descriptions

If the environment variable TERMINFO is set, it is interpreted as the pathname of a directory containing the compiled description you are working on. Only that directory is searched.

If TERMINFO is not set, the ncurses version of the terminfo reader code will instead look in the directory $HOME/.terminfo for a compiled description. If it fails to find one there, and the environment variable TERMINFO_DIRS is set, it will interpret the contents of that variable as a list of colon- separated directories to be searched (an empty entry is interpreted as a command to search /usr/share/terminfo). If no description is found in any of the TERMINFO_DIRS directories, the fetch fails.

If neither TERMINFO nor TERMINFO_DIRS is set, the last place tried will be the system terminfo directory, /usr/share/terminfo.

(Neither the $HOME/.terminfo lookups nor TERMINFO_DIRS extensions are supported under stock System V terminfo/curses.)

Preparing Descriptions

We now outline how to prepare descriptions of terminals. The most effective way to prepare a terminal description is by imitating the description of a similar terminal in terminfo and to build up a description gradually, using partial descriptions with vi or some other screen-oriented program to check that they are correct. Be aware that a very unusual terminal may expose deficiencies in the ability of the terminfo file to describe it or bugs in the screen-handling code of the test program.

To get the padding for insert line right (if the terminal manufacturer did not document it) a severe test is to edit a large file at 9600 baud, delete 16 or so lines from the middle of the screen, then hit the ‘u’ key several times quickly. If the terminal messes up, more padding is usually needed. A similar test can be used for insert character.

Basic Capabilities

The number of columns on each line for the terminal is given by the cols numeric capability. If the terminal is a CRT, then the number of lines on the screen is given by the lines capability. If the terminal wraps around to the beginning of the next line when it reaches the right margin, then it should have the am capability. If the terminal can clear its screen, leaving the cursor in the home position, then this is given by the clear string capability. If the terminal overstrikes (rather than clearing a position when a character is struck over) then it should have the os capability. If the terminal is a printing terminal, with no soft copy unit, give it both hc and os. (os applies to storage scope terminals, such as TEKTRONIX 4010 series, as well as hard copy and APL terminals.) If there is a code to move the cursor to the left edge of the current row, give this as cr. (Normally this will be carriage return, control M.) If there is a code to produce an audible signal (bell, beep, etc) give this as bel.

If there is a code to move the cursor one position to the left (such as backspace) that capability should be given as cub1. Similarly, codes to move to the right, up, and down should be given as cuf1, cuu1, and cud1. These local cursor motions should not alter the text they pass over, for example, you would not normally use ‘cuf1= ’ because the space would erase the character moved over.

A very important point here is that the local cursor motions encoded in terminfo are undefined at the left and top edges of a CRT terminal. Programs should never attempt to backspace around the left edge, unless bw is given, and never attempt to go up locally off the top. In order to scroll text up, a program will go to the bottom left corner of the screen and send the ind (index) string.

To scroll text down, a program goes to the top left corner of the screen and sends the ri (reverse index) string. The strings ind and ri are undefined when not on their respective corners of the screen.

Parameterized versions of the scrolling sequences are indn and rin which have the same semantics as ind and ri except that they take one parameter, and scroll that many lines. They are also undefined except at the appropriate edge of the screen.

The am capability tells whether the cursor sticks at the right edge of the screen when text is output, but this does not necessarily apply to a cuf1 from the last column. The only local motion which is defined from the left edge is if bw is given, then a cub1 from the left edge will move to the right edge of the previous row. If bw is not given, the effect is undefined. This is useful for drawing a box around the edge of the screen, for example. If the terminal has switch selectable automatic margins, the terminfo file usually assumes that this is on; i.e., am. If the terminal has a command which moves to the first column of the next line, that command can be given as nel (newline). It does not matter if the command clears the remainder of the current line, so if the terminal has no cr and lf it may still be possible to craft a working nel out of one or both of them.

These capabilities suffice to describe hard-copy and “glass-tty” terminals. Thus the model 33 teletype is described as

33|tty33|tty|model 33 teletype,
        bel=^G, cols#72, cr=^M, cud1=^J, hc, ind=^J, os,

while the Lear Siegler ADM-3 is described as

adm3|3|lsi adm3,
        am, bel=^G, clear=^Z, cols#80, cr=^M, cub1=^H, cud1=^J,
        ind=^J, lines#24,

Parameterized Strings

Cursor addressing and other strings requiring parameters in the terminal are described by a parameterized string capability, with printf(3) like escapes %x in it. For example, to address the cursor, the cup capability is given, using two parameters: the row and column to address to. (Rows and columns are numbered from zero and refer to the physical screen visible to the user, not to any unseen memory.) If the terminal has memory relative cursor addressing, that can be indicated by mrcup.

The parameter mechanism uses a stack and special % codes to manipulate it. Typically a sequence will push one of the parameters onto the stack and then print it in some format. Print (e.g., "%d") is a special case. Other operations, including "%t" pop their operand from the stack. It is noted that more complex operations are often necessary, e.g., in the sgr string.

The % encodings have the following meanings:

%% outputs ‘%’
%[[:]flags][width[.precision]][doxXs]
 as in printf, flags are [-+#] and space. Use a ‘:’ to allow the next character to be a ‘-’ flag, avoiding interpreting "%-" as an operator.
%c print pop() like %c in printf
%s print pop() like %s in printf
%p[1-9]
 push i’th parameter
%P[a-z]
 set dynamic variable [a-z] to pop()
%g[a-z]
 get dynamic variable [a-z] and push it
%P[A-Z]
 set static variable [a-z] to pop()
%g[A-Z]
 get static variable [a-z] and push it
The terms "static" and "dynamic" are misleading. Historically, these are simply two different sets of variables, whose values are not reset between calls to tparm. However, that fact is not documented in other implementations. Relying on it will adversely impact portability to other implementations.
%’cchar constant c
%{nn} integer constant nn
%l push strlen(pop)
%+ %- %* %/ %m
 arithmetic (%m is mod): push(pop() op pop())
%& %| %^
 bit operations (AND, OR and exclusive-OR): push(pop() op pop())
%= %> %<
 logical operations: push(pop() op pop())
%A, %O logical AND and OR operations (for conditionals)
%! %~ unary operations (logical and bit complement): push(op pop())
%i add 1 to first two parameters (for ANSI terminals)
%? expr %t thenpart %e elsepart %;
 This forms an if-then-else. The %e elsepart is optional. Usually the %? expr part pushes a value onto the stack, and %t pops it from the stack, testing if it is nonzero (true). If it is zero (false), control passes to the %e (else) part.
It is possible to form else-if’s a la Algol 68: %? c1 %t b1 %e c2 %t b2 %e c3 %t b3 %e c4 %t b4 %e %;
where ci are conditions, bi are bodies.
Use the -f option of tic or infocmp to see the structure of if-the-else’s. Some strings, e.g., sgr can be very complicated when written on one line. The -f option splits the string into lines with the parts indented.
Binary operations are in postfix form with the operands in the usual order. That is, to get x-5 one would use "%gx%{5}%-". %P and %g variables are persistent across escape-string evaluations.

Consider the HP2645, which, to get to row 3 and column 12, needs to be sent \E&a12c03Y padded for 6 milliseconds. Note that the order of the rows and columns is inverted here, and that the row and column are printed as two digits. Thus its cup capability is “cup=6\E&%p2%2dc%p1%2dY”.

The Microterm ACT-IV needs the current row and column sent preceded by a ^T, with the row and column simply encoded in binary, “cup=^T%p1%c%p2%c”. Terminals which use “%c” need to be able to backspace the cursor (cub1), and to move the cursor up one line on the screen (cuu1). This is necessary because it is not always safe to transmit \n ^D and \r, as the system may change or discard them. (The library routines dealing with terminfo set tty modes so that tabs are never expanded, so \t is safe to send. This turns out to be essential for the Ann Arbor 4080.)

A final example is the LSI ADM-3a, which uses row and column offset by a blank character, thus “cup=\E=%p1%’ ’%+%c%p2%’ ’%+%c”. After sending ‘\E=’, this pushes the first parameter, pushes the ASCII value for a space (32), adds them (pushing the sum on the stack in place of the two previous values) and outputs that value as a character. Then the same is done for the second parameter. More complex arithmetic is possible using the stack.

Cursor Motions

If the terminal has a fast way to home the cursor (to very upper left corner of screen) then this can be given as home; similarly a fast way of getting to the lower left-hand corner can be given as ll; this may involve going up with cuu1 from the home position, but a program should never do this itself (unless ll does) because it can make no assumption about the effect of moving up from the home position. Note that the home position is the same as addressing to (0,0): to the top left corner of the screen, not of memory. (Thus, the \EH sequence on HP terminals cannot be used for home.)

If the terminal has row or column absolute cursor addressing, these can be given as single parameter capabilities hpa (horizontal position absolute) and vpa (vertical position absolute). Sometimes these are shorter than the more general two parameter sequence (as with the hp2645) and can be used in preference to cup. If there are parameterized local motions (e.g., move n spaces to the right) these can be given as cud, cub, cuf, and cuu with a single parameter indicating how many spaces to move. These are primarily useful if the terminal does not have cup, such as the TEKTRONIX 4025.

If the terminal needs to be in a special mode when running a program that uses these capabilities, the codes to enter and exit this mode can be given as smcup and rmcup. This arises, for example, from terminals like the Concept with more than one page of memory. If the terminal has only memory relative cursor addressing and not screen relative cursor addressing, a one screen-sized window must be fixed into the terminal for cursor addressing to work properly. This is also used for the TEKTRONIX 4025, where smcup sets the command character to be the one used by terminfo. If the smcup sequence will not restore the screen after an rmcup sequence is output (to the state prior to outputting rmcup), specify nrrmc.

Area Clears

If the terminal can clear from the current position to the end of the line, leaving the cursor where it is, this should be given as el. If the terminal can clear from the beginning of the line to the current position inclusive, leaving the cursor where it is, this should be given as el1. If the terminal can clear from the current position to the end of the display, then this should be given as ed. Ed is only defined from the first column of a line. (Thus, it can be simulated by a request to delete a large number of lines, if a true ed is not available.)

Insert/delete line and vertical motions

If the terminal can open a new blank line before the line where the cursor is, this should be given as il1; this is done only from the first position of a line. The cursor must then appear on the newly blank line. If the terminal can delete the line which the cursor is on, then this should be given as dl1; this is done only from the first position on the line to be deleted. Versions of il1 and dl1 which take a single parameter and insert or delete that many lines can be given as il and dl.

If the terminal has a settable scrolling region (like the vt100) the command to set this can be described with the csr capability, which takes two parameters: the top and bottom lines of the scrolling region. The cursor position is, alas, undefined after using this command.

It is possible to get the effect of insert or delete line using csr on a properly chosen region; the sc and rc (save and restore cursor) commands may be useful for ensuring that your synthesized insert/delete string does not move the cursor. (Note that the ncurses(3NCURSES) library does this synthesis automatically, so you need not compose insert/delete strings for an entry with csr).

Yet another way to construct insert and delete might be to use a combination of index with the memory-lock feature found on some terminals (like the HP-700/90 series, which however also has insert/delete).

Inserting lines at the top or bottom of the screen can also be done using ri or ind on many terminals without a true insert/delete line, and is often faster even on terminals with those features.

The boolean non_dest_scroll_region should be set if each scrolling window is effectively a view port on a screen-sized canvas. To test for this capability, create a scrolling region in the middle of the screen, write something to the bottom line, move the cursor to the top of the region, and do ri followed by dl1 or ind. If the data scrolled off the bottom of the region by the ri re-appears, then scrolling is non-destructive. System V and XSI Curses expect that ind, ri, indn, and rin will simulate destructive scrolling; their documentation cautions you not to define csr unless this is true. This curses implementation is more liberal and will do explicit erases after scrolling if ndstr is defined.

If the terminal has the ability to define a window as part of memory, which all commands affect, it should be given as the parameterized string wind. The four parameters are the starting and ending lines in memory and the starting and ending columns in memory, in that order.

If the terminal can retain display memory above, then the da capability should be given; if display memory can be retained below, then db should be given. These indicate that deleting a line or scrolling may bring non-blank lines up from below or that scrolling back with ri may bring down non-blank lines.

Insert/Delete Character

There are two basic kinds of intelligent terminals with respect to insert/delete character which can be described using terminfo. The most common insert/delete character operations affect only the characters on the current line and shift characters off the end of the line rigidly. Other terminals, such as the Concept 100 and the Perkin Elmer Owl, make a distinction between typed and untyped blanks on the screen, shifting upon an insert or delete only to an untyped blank on the screen which is either eliminated, or expanded to two untyped blanks. You can determine the kind of terminal you have by clearing the screen and then typing text separated by cursor motions. Type “abc def” using local cursor motions (not spaces) between the “abc” and the “def”. Then position the cursor before the “abc” and put the terminal in insert mode. If typing characters causes the rest of the line to shift rigidly and characters to fall off the end, then your terminal does not distinguish between blanks and untyped positions. If the “abc” shifts over to the “def” which then move together around the end of the current line and onto the next as you insert, you have the second type of terminal, and should give the capability in, which stands for “insert null”. While these are two logically separate attributes (one line versus multi-line insert mode, and special treatment of untyped spaces) we have seen no terminals whose insert mode cannot be described with the single attribute.

Terminfo can describe both terminals which have an insert mode, and terminals which send a simple sequence to open a blank position on the current line. Give as smir the sequence to get into insert mode. Give as rmir the sequence to leave insert mode. Now give as ich1 any sequence needed to be sent just before sending the character to be inserted. Most terminals with a true insert mode will not give ich1; terminals which send a sequence to open a screen position should give it here.

If your terminal has both, insert mode is usually preferable to ich1. Technically, you should not give both unless the terminal actually requires both to be used in combination. Accordingly, some non-curses applications get confused if both are present; the symptom is doubled characters in an update using insert. This requirement is now rare; most ich sequences do not require previous smir, and most smir insert modes do not require ich1 before each character. Therefore, the new curses actually assumes this is the case and uses either rmir/smir or ich/ich1 as appropriate (but not both). If you have to write an entry to be used under new curses for a terminal old enough to need both, include the rmir/smir sequences in ich1.

If post insert padding is needed, give this as a number of milliseconds in ip (a string option). Any other sequence which may need to be sent after an insert of a single character may also be given in ip. If your terminal needs both to be placed into an ‘insert mode’ and a special code to precede each inserted character, then both smir/rmir and ich1 can be given, and both will be used. The ich capability, with one parameter, n, will repeat the effects of ich1 n times.

If padding is necessary between characters typed while not in insert mode, give this as a number of milliseconds padding in rmp.

It is occasionally necessary to move around while in insert mode to delete characters on the same line (e.g., if there is a tab after the insertion position). If your terminal allows motion while in insert mode you can give the capability mir to speed up inserting in this case. Omitting mir will affect only speed. Some terminals (notably Datamedia’s) must not have mir because of the way their insert mode works.

Finally, you can specify dch1 to delete a single character, dch with one parameter, n, to delete n characters, and delete mode by giving smdc and rmdc to enter and exit delete mode (any mode the terminal needs to be placed in for dch1 to work).

A command to erase n characters (equivalent to outputting n blanks without moving the cursor) can be given as ech with one parameter.

Highlighting, Underlining, and Visible Bells

If your terminal has one or more kinds of display attributes, these can be represented in a number of different ways. You should choose one display form as standout mode, representing a good, high contrast, easy-on-the-eyes, format for highlighting error messages and other attention getters. (If you have a choice, reverse video plus half-bright is good, or reverse video alone.) The sequences to enter and exit standout mode are given as smso and rmso, respectively. If the code to change into or out of standout mode leaves one or even two blank spaces on the screen, as the TVI 912 and Teleray 1061 do, then xmc should be given to tell how many spaces are left.

Codes to begin underlining and end underlining can be given as smul and rmul respectively. If the terminal has a code to underline the current character and move the cursor one space to the right, such as the Microterm Mime, this can be given as uc.

Other capabilities to enter various highlighting modes include blink (blinking) bold (bold or extra bright) dim (dim or half-bright) invis (blanking or invisible text) prot (protected) rev (reverse video) sgr0 (turn off all attribute modes) smacs (enter alternate character set mode) and rmacs (exit alternate character set mode). Turning on any of these modes singly may or may not turn off other modes.

If there is a sequence to set arbitrary combinations of modes, this should be given as sgr (set attributes), taking 9 parameters. Each parameter is either 0 or nonzero, as the corresponding attribute is on or off. The 9 parameters are, in order: standout, underline, reverse, blink, dim, bold, blank, protect, alternate character set. Not all modes need be supported by sgr, only those for which corresponding separate attribute commands exist.

For example, the DEC vt220 supports most of the modes:

tparm parameterattributeescape sequence
nonenone\E[0m 
p1standout\E[0;1;7m 
p2underline\E[0;4m 
p3reverse\E[0;7m 
p4blink\E[0;5m 
p5dimnot available 
p6bold\E[0;1m 
p7invis\E[0;8m 
p8protectnot used 
p9altcharset^O (off) ^N (on) 

We begin each escape sequence by turning off any existing modes, since there is no quick way to determine whether they are active. Standout is set up to be the combination of reverse and bold. The vt220 terminal has a protect mode, though it is not commonly used in sgr because it protects characters on the screen from the host’s erasures. The altcharset mode also is different in that it is either ^O or ^N, depending on whether it is off or on. If all modes are turned on, the resulting sequence is \E[0;1;4;5;7;8m^N.

Some sequences are common to different modes. For example, ;7 is output when either p1 or p3 is true, that is, if either standout or reverse modes are turned on.

Writing out the above sequences, along with their dependencies yields

sequencewhen to outputterminfo translation
\E[0always\E[0 
;1if p1 or p6%?%p1%p6%|%t;1%; 
;4if p2%?%p2%|%t;4%; 
;5if p4%?%p4%|%t;5%; 
;7if p1 or p3%?%p1%p3%|%t;7%; 
;8if p7%?%p7%|%t;8%; 
malwaysm 
^N or ^Oif p9 ^N, else ^O%?%p9%t^N%e^O%; 

Putting this all together into the sgr sequence gives:

sgr=\E[0%?%p1%p6%|%t;1%;%?%p2%t;4%;%?%p1%p3%|%t;7%; %?%p4%t;5%;%?%p7%t;8%;m%?%p9%t\016%e\017%;,

Remember that if you specify sgr, you must also specify sgr0. Also, some implementations rely on sgr being given if sgr0 is, Not all terminfo entries necessarily have an sgr string, however. Many terminfo entries are derived from termcap entries which have no sgr string. The only drawback to adding an sgr string is that termcap also assumes that sgr0 does not exit alternate character set mode.

Terminals with the ‘‘magic cookie’’ glitch (xmc) deposit special ‘‘cookies’’ when they receive mode-setting sequences, which affect the display algorithm rather than having extra bits for each character. Some terminals, such as the HP 2621, automatically leave standout mode when they move to a new line or the cursor is addressed. Programs using standout mode should exit standout mode before moving the cursor or sending a newline, unless the msgr capability, asserting that it is safe to move in standout mode, is present.

If the terminal has a way of flashing the screen to indicate an error quietly (a bell replacement) then this can be given as flash; it must not move the cursor.

If the cursor needs to be made more visible than normal when it is not on the bottom line (to make, for example, a non-blinking underline into an easier to find block or blinking underline) give this sequence as cvvis. If there is a way to make the cursor completely invisible, give that as civis. The capability cnorm should be given which undoes the effects of both of these modes.

If your terminal correctly generates underlined characters (with no special codes needed) even though it does not overstrike, then you should give the capability ul. If a character overstriking another leaves both characters on the screen, specify the capability os. If overstrikes are erasable with a blank, then this should be indicated by giving eo.

Keypad and Function Keys

If the terminal has a keypad that transmits codes when the keys are pressed, this information can be given. Note that it is not possible to handle terminals where the keypad only works in local (this applies, for example, to the unshifted HP 2621 keys). If the keypad can be set to transmit or not transmit, give these codes as smkx and rmkx. Otherwise the keypad is assumed to always transmit. The codes sent by the left arrow, right arrow, up arrow, down arrow, and home keys can be given as kcub1, kcuf1, kcuu1, kcud1, and khome respectively. If there are function keys such as f0, f1, ..., f10, the codes they send can be given as kf0, kf1, ..., kf10. If these keys have labels other than the default f0 through f10, the labels can be given as lf0, lf1, ..., lf10. The codes transmitted by certain other special keys can be given: kll (home down), kbs (backspace), ktbc (clear all tabs), kctab (clear the tab stop in this column), kclr (clear screen or erase key), kdch1 (delete character), kdl1 (delete line), krmir (exit insert mode), kel (clear to end of line), ked (clear to end of screen), kich1 (insert character or enter insert mode), kil1 (insert line), knp (next page), kpp (previous page), kind (scroll forward/down), kri (scroll backward/up), khts (set a tab stop in this column). In addition, if the keypad has a 3 by 3 array of keys including the four arrow keys, the other five keys can be given as ka1, ka3, kb2, kc1, and kc3. These keys are useful when the effects of a 3 by 3 directional pad are needed.

Strings to program function keys can be given as pfkey, pfloc, and pfx. A string to program screen labels should be specified as pln. Each of these strings takes two parameters: the function key number to program (from 0 to 10) and the string to program it with. Function key numbers out of this range may program undefined keys in a terminal dependent manner. The difference between the capabilities is that pfkey causes pressing the given key to be the same as the user typing the given string; pfloc causes the string to be executed by the terminal in local; and pfx causes the string to be transmitted to the computer.

The capabilities nlab, lw and lh define the number of programmable screen labels and their width and height. If there are commands to turn the labels on and off, give them in smln and rmln. smln is normally output after one or more pln sequences to make sure that the change becomes visible.

Tabs and Initialization

If the terminal has hardware tabs, the command to advance to the next tab stop can be given as ht (usually control I). A ‘‘back-tab’’ command which moves leftward to the preceding tab stop can be given as cbt. By convention, if the teletype modes indicate that tabs are being expanded by the computer rather than being sent to the terminal, programs should not use ht or cbt even if they are present, since the user may not have the tab stops properly set. If the terminal has hardware tabs which are initially set every n spaces when the terminal is powered up, the numeric parameter it is given, showing the number of spaces the tabs are set to. This is normally used by the tset command to determine whether to set the mode for hardware tab expansion, and whether to set the tab stops. If the terminal has tab stops that can be saved in non-volatile memory, the terminfo description can assume that they are properly set.

Other capabilities include is1, is2, and is3, initialization strings for the terminal, iprog, the path name of a program to be run to initialize the terminal, and if, the name of a file containing long initialization strings. These strings are expected to set the terminal into modes consistent with the rest of the terminfo description. They are normally sent to the terminal, by the init option of the tput program, each time the user logs in. They will be printed in the following order:

run the program
 iprog
output is1 is2
set the margins using
 mgc, smgl and smgr
set tabs using
 tbc and hts
print the file
 if
and finally
 output is3.

Most initialization is done with is2. Special terminal modes can be set up without duplicating strings by putting the common sequences in is2 and special cases in is1 and is3.

A set of sequences that does a harder reset from a totally unknown state can be given as rs1, rs2, rf and rs3, analogous to is1 , is2 , if and is3 respectively. These strings are output by the reset program, which is used when the terminal gets into a wedged state. Commands are normally placed in rs1, rs2 rs3 and rf only if they produce annoying effects on the screen and are not necessary when logging in. For example, the command to set the vt100 into 80-column mode would normally be part of is2, but it causes an annoying glitch of the screen and is not normally needed since the terminal is usually already in 80 column mode.

The reset program writes strings including iprog, etc., in the same order as the init program, using rs1, etc., instead of is1, etc. If any of rs1, rs2, rs3, or rf reset capability strings are missing, the reset program falls back upon the corresponding initialization capability string.

If there are commands to set and clear tab stops, they can be given as tbc (clear all tab stops) and hts (set a tab stop in the current column of every row). If a more complex sequence is needed to set the tabs than can be described by this, the sequence can be placed in is2 or if.

Delays and Padding

Many older and slower terminals do not support either XON/XOFF or DTR handshaking, including hard copy terminals and some very archaic CRTs (including, for example, DEC VT100s). These may require padding characters after certain cursor motions and screen changes.

If the terminal uses xon/xoff handshaking for flow control (that is, it automatically emits ^S back to the host when its input buffers are close to full), set xon. This capability suppresses the emission of padding. You can also set it for memory-mapped console devices effectively that do not have a speed limit. Padding information should still be included so that routines can make better decisions about relative costs, but actual pad characters will not be transmitted.

If pb (padding baud rate) is given, padding is suppressed at baud rates below the value of pb. If the entry has no padding baud rate, then whether padding is emitted or not is completely controlled by xon.

If the terminal requires other than a null (zero) character as a pad, then this can be given as pad. Only the first character of the pad string is used.

Status Lines

Some terminals have an extra ‘status line’ which is not normally used by software (and thus not counted in the terminal’s lines capability).

The simplest case is a status line which is cursor-addressable but not part of the main scrolling region on the screen; the Heathkit H19 has a status line of this kind, as would a 24-line VT100 with a 23-line scrolling region set up on initialization. This situation is indicated by the hs capability.

Some terminals with status lines need special sequences to access the status line. These may be expressed as a string with single parameter tsl which takes the cursor to a given zero-origin column on the status line. The capability fsl must return to the main-screen cursor positions before the last tsl. You may need to embed the string values of sc (save cursor) and rc (restore cursor) in tsl and fsl to accomplish this.

The status line is normally assumed to be the same width as the width of the terminal. If this is untrue, you can specify it with the numeric capability wsl.

A command to erase or blank the status line may be specified as dsl.

The boolean capability eslok specifies that escape sequences, tabs, etc., work ordinarily in the status line.

The ncurses implementation does not yet use any of these capabilities. They are documented here in case they ever become important.

Line Graphics

Many terminals have alternate character sets useful for forms-drawing. Terminfo and curses build in support for the drawing characters supported by the VT100, with some characters from the AT&T 4410v1 added. This alternate character set may be specified by the acsc capability.

GlyphACSAsciiVT100
NameNameDefaultName
UK pound signACS_STERLINGf}
arrow pointing downACS_DARROWv.
arrow pointing leftACS_LARROW<,
arrow pointing rightACS_RARROW>+
arrow pointing upACS_UARROW^-
board of squaresACS_BOARD#h
bulletACS_BULLETo~
checker board (stipple)ACS_CKBOARD:a
degree symbolACS_DEGREE\f
diamondACS_DIAMOND+
greater-than-or-equal-toACS_GEQUAL>z
greek piACS_PI*{
horizontal lineACS_HLINE-q
lantern symbolACS_LANTERN#i
large plus or crossoverACS_PLUS+n
less-than-or-equal-toACS_LEQUAL<y
lower left cornerACS_LLCORNER+m
lower right cornerACS_LRCORNER+j
not-equalACS_NEQUAL!|
plus/minusACS_PLMINUS#g
scan line 1ACS_S1~o
scan line 3ACS_S3-p
scan line 7ACS_S7-r
scan line 9ACS_S9_s
solid square blockACS_BLOCK#0
tee pointing downACS_TTEE+w
tee pointing leftACS_RTEE+u
tee pointing rightACS_LTEE+t
tee pointing upACS_BTEE+v
upper left cornerACS_ULCORNER+l
upper right cornerACS_URCORNER+k
vertical lineACS_VLINE|x

The best way to define a new device’s graphics set is to add a column to a copy of this table for your terminal, giving the character which (when emitted between smacs/rmacs switches) will be rendered as the corresponding graphic. Then read off the VT100/your terminal character pairs right to left in sequence; these become the ACSC string.

Color Handling

Most color terminals are either ‘Tektronix-like’ or ‘HP-like’. Tektronix-like terminals have a predefined set of N colors (where N usually 8), and can set character-cell foreground and background characters independently, mixing them into N * N color-pairs. On HP-like terminals, the use must set each color pair up separately (foreground and background are not independently settable). Up to M color-pairs may be set up from 2*M different colors. ANSI-compatible terminals are Tektronix-like.

Some basic color capabilities are independent of the color method. The numeric capabilities colors and pairs specify the maximum numbers of colors and color-pairs that can be displayed simultaneously. The op (original pair) string resets foreground and background colors to their default values for the terminal. The oc string resets all colors or color-pairs to their default values for the terminal. Some terminals (including many PC terminal emulators) erase screen areas with the current background color rather than the power-up default background; these should have the boolean capability bce.

To change the current foreground or background color on a Tektronix-type terminal, use setaf (set ANSI foreground) and setab (set ANSI background) or setf (set foreground) and setb (set background). These take one parameter, the color number. The SVr4 documentation describes only setaf/setab; the XPG4 draft says that "If the terminal supports ANSI escape sequences to set background and foreground, they should be coded as setaf and setab, respectively. If the terminal supports other escape sequences to set background and foreground, they should be coded as setf and setb, respectively. The vidputs() function and the refresh functions use setaf and setab if they are defined."

The setaf/setab and setf/setb capabilities take a single numeric argument each. Argument values 0-7 of setaf/setab are portably defined as follows (the middle column is the symbolic #define available in the header for the curses or ncurses libraries). The terminal hardware is free to map these as it likes, but the RGB values indicate normal locations in color space.

Color#defineValueRGB
blackCOLOR_BLACK00, 0, 0
redCOLOR_RED 1max,0,0
greenCOLOR_GREEN20,max,0
yellowCOLOR_YELLOW3max,max,0
blueCOLOR_BLUE40,0,max
magentaCOLOR_MAGENTA5max,0,max
cyanCOLOR_CYAN60,max,max
whiteCOLOR_WHITE7max,max,max

The argument values of setf/setb historically correspond to a different mapping, i.e.,
Color#defineValueRGB
blackCOLOR_BLACK00, 0, 0
blueCOLOR_BLUE10,0,max
greenCOLOR_GREEN20,max,0
cyanCOLOR_CYAN30,max,max
redCOLOR_RED 4max,0,0
magentaCOLOR_MAGENTA5max,0,max
yellowCOLOR_YELLOW6max,max,0
whiteCOLOR_WHITE7max,max,max
It is important to not confuse the two sets of color capabilities; otherwise red/blue will be interchanged on the display.

On an HP-like terminal, use scp with a color-pair number parameter to set which color pair is current.

On a Tektronix-like terminal, the capability ccc may be present to indicate that colors can be modified. If so, the initc capability will take a color number (0 to colors - 1)and three more parameters which describe the color. These three parameters default to being interpreted as RGB (Red, Green, Blue) values. If the boolean capability hls is present, they are instead as HLS (Hue, Lightness, Saturation) indices. The ranges are terminal-dependent.

On an HP-like terminal, initp may give a capability for changing a color-pair value. It will take seven parameters; a color-pair number (0 to max_pairs - 1), and two triples describing first background and then foreground colors. These parameters must be (Red, Green, Blue) or (Hue, Lightness, Saturation) depending on hls.

On some color terminals, colors collide with highlights. You can register these collisions with the ncv capability. This is a bit-mask of attributes not to be used when colors are enabled. The correspondence with the attributes understood by curses is as follows:

AttributeBitDecimal
A_STANDOUT01
A_UNDERLINE12
A_REVERSE24
A_BLINK38
A_DIM416
A_BOLD532
A_INVIS664
A_PROTECT7128
A_ALTCHARSET8256

For example, on many IBM PC consoles, the underline attribute collides with the foreground color blue and is not available in color mode. These should have an ncv capability of 2.

SVr4 curses does nothing with ncv, ncurses recognizes it and optimizes the output in favor of colors.

Miscellaneous

If the terminal requires other than a null (zero) character as a pad, then this can be given as pad. Only the first character of the pad string is used. If the terminal does not have a pad character, specify npc. Note that ncurses implements the termcap-compatible PC variable; though the application may set this value to something other than a null, ncurses will test npc first and use napms if the terminal has no pad character.

If the terminal can move up or down half a line, this can be indicated with hu (half-line up) and hd (half-line down). This is primarily useful for superscripts and subscripts on hard-copy terminals. If a hard-copy terminal can eject to the next page (form feed), give this as ff (usually control L).

If there is a command to repeat a given character a given number of times (to save time transmitting a large number of identical characters) this can be indicated with the parameterized string rep. The first parameter is the character to be repeated and the second is the number of times to repeat it. Thus, tparm(repeat_char, ’x’, 10) is the same as ‘xxxxxxxxxx’.

If the terminal has a settable command character, such as the TEKTRONIX 4025, this can be indicated with cmdch. A prototype command character is chosen which is used in all capabilities. This character is given in the cmdch capability to identify it. The following convention is supported on some UNIX systems: The environment is to be searched for a CC variable, and if found, all occurrences of the prototype character are replaced with the character in the environment variable.

Terminal descriptions that do not represent a specific kind of known terminal, such as switch, dialup, patch, and network, should include the gn (generic) capability so that programs can complain that they do not know how to talk to the terminal. (This capability does not apply to virtual terminal descriptions for which the escape sequences are known.)

If the terminal has a ‘‘meta key’’ which acts as a shift key, setting the 8th bit of any character transmitted, this fact can be indicated with km. Otherwise, software will assume that the 8th bit is parity and it will usually be cleared. If strings exist to turn this ‘‘meta mode’’ on and off, they can be given as smm and rmm.

If the terminal has more lines of memory than will fit on the screen at once, the number of lines of memory can be indicated with lm. A value of lm#0 indicates that the number of lines is not fixed, but that there is still more memory than fits on the screen.

If the terminal is one of those supported by the UNIX virtual terminal protocol, the terminal number can be given as vt.

Media copy strings which control an auxiliary printer connected to the terminal can be given as mc0: print the contents of the screen, mc4: turn off the printer, and mc5: turn on the printer. When the printer is on, all text sent to the terminal will be sent to the printer. It is undefined whether the text is also displayed on the terminal screen when the printer is on. A variation mc5p takes one parameter, and leaves the printer on for as many characters as the value of the parameter, then turns the printer off. The parameter should not exceed 255. All text, including mc4, is transparently passed to the printer while an mc5p is in effect.

Glitches and Braindamage

Hazeltine terminals, which do not allow ‘~’ characters to be displayed should indicate hz.

Terminals which ignore a line-feed immediately after an am wrap, such as the Concept and vt100, should indicate xenl.

If el is required to get rid of standout (instead of merely writing normal text on top of it), xhp should be given.

Teleray terminals, where tabs turn all characters moved over to blanks, should indicate xt (destructive tabs). Note: the variable indicating this is now ‘dest_tabs_magic_smso’; in older versions, it was teleray_glitch. This glitch is also taken to mean that it is not possible to position the cursor on top of a ‘‘magic cookie’’, that to erase standout mode it is instead necessary to use delete and insert line. The ncurses implementation ignores this glitch.

The Beehive Superbee, which is unable to correctly transmit the escape or control C characters, has xsb, indicating that the f1 key is used for escape and f2 for control C. (Only certain Superbees have this problem, depending on the ROM.) Note that in older terminfo versions, this capability was called ‘beehive_glitch’; it is now ‘no_esc_ctl_c’.

Other specific terminal problems may be corrected by adding more capabilities of the form xx.

Similar Terminals

If there are two very similar terminals, one (the variant) can be defined as being just like the other (the base) with certain exceptions. In the definition of the variant, the string capability use can be given with the name of the base terminal. The capabilities given before use override those in the base type named by use. If there are multiple use capabilities, they are merged in reverse order. That is, the rightmost use reference is processed first, then the one to its left, and so forth. Capabilities given explicitly in the entry override those brought in by use references.

A capability can be canceled by placing xx@ to the left of the use reference that imports it, where xx is the capability. For example, the entry

        2621-nl, smkx@, rmkx@, use=2621,

defines a 2621-nl that does not have the smkx or rmkx capabilities, and hence does not turn on the function key labels when in visual mode. This is useful for different modes for a terminal, or for different user preferences.

Pitfalls of Long Entries

Long terminfo entries are unlikely to be a problem; to date, no entry has even approached terminfo’s 4096-byte string-table maximum. Unfortunately, the termcap translations are much more strictly limited (to 1023 bytes), thus termcap translations of long terminfo entries can cause problems.

The man pages for 4.3BSD and older versions of tgetent() instruct the user to allocate a 1024-byte buffer for the termcap entry. The entry gets null-terminated by the termcap library, so that makes the maximum safe length for a termcap entry 1k-1 (1023) bytes. Depending on what the application and the termcap library being used does, and where in the termcap file the terminal type that tgetent() is searching for is, several bad things can happen.

Some termcap libraries print a warning message or exit if they find an entry that’s longer than 1023 bytes; others do not; others truncate the entries to 1023 bytes. Some application programs allocate more than the recommended 1K for the termcap entry; others do not.

Each termcap entry has two important sizes associated with it: before "tc" expansion, and after "tc" expansion. "tc" is the capability that tacks on another termcap entry to the end of the current one, to add on its capabilities. If a termcap entry does not use the "tc" capability, then of course the two lengths are the same.

The "before tc expansion" length is the most important one, because it affects more than just users of that particular terminal. This is the length of the entry as it exists in /etc/termcap, minus the backslash-newline pairs, which tgetent() strips out while reading it. Some termcap libraries strip off the final newline, too (GNU termcap does not). Now suppose:
* a termcap entry before expansion is more than 1023 bytes long,
* and the application has only allocated a 1k buffer,
* and the termcap library (like the one in BSD/OS 1.1 and GNU) reads the whole entry into the buffer, no matter what its length, to see if it is the entry it wants,
* and tgetent() is searching for a terminal type that either is the long entry, appears in the termcap file after the long entry, or does not appear in the file at all (so that tgetent() has to search the whole termcap file).
Then tgetent() will overwrite memory, perhaps its stack, and probably core dump the program. Programs like telnet are particularly vulnerable; modern telnets pass along values like the terminal type automatically. The results are almost as undesirable with a termcap library, like SunOS 4.1.3 and Ultrix 4.4, that prints warning messages when it reads an overly long termcap entry. If a termcap library truncates long entries, like OSF/1 3.0, it is immune to dying here but will return incorrect data for the terminal.

The "after tc expansion" length will have a similar effect to the above, but only for people who actually set TERM to that terminal type, since tgetent() only does "tc" expansion once it is found the terminal type it was looking for, not while searching.

In summary, a termcap entry that is longer than 1023 bytes can cause, on various combinations of termcap libraries and applications, a core dump, warnings, or incorrect operation. If it is too long even before "tc" expansion, it will have this effect even for users of some other terminal types and users whose TERM variable does not have a termcap entry.

When in -C (translate to termcap) mode, the ncurses implementation of tic(1) issues warning messages when the pre-tc length of a termcap translation is too long. The -c (check) option also checks resolved (after tc expansion) lengths.

Binary Compatibility

It is not wise to count on portability of binary terminfo entries between commercial UNIX versions. The problem is that there are at least two versions of terminfo (under HP-UX and AIX) which diverged from System V terminfo after SVr1, and have added extension capabilities to the string table that (in the binary format) collide with System V and XSI Curses extensions.

EXTENSIONS


Some SVr4 curses implementations, and all previous to SVr4, do not interpret the %A and %O operators in parameter strings.

SVr4/XPG4 do not specify whether msgr licenses movement while in an alternate-character-set mode (such modes may, among other things, map CR and NL to characters that do not trigger local motions). The ncurses implementation ignores msgr in ALTCHARSET mode. This raises the possibility that an XPG4 implementation making the opposite interpretation may need terminfo entries made for ncurses to have msgr turned off.

The ncurses library handles insert-character and insert-character modes in a slightly non-standard way to get better update efficiency. See the Insert/Delete Character subsection above.

The parameter substitutions for set_clock and display_clock are not documented in SVr4 or the XSI Curses standard. They are deduced from the documentation for the AT&T 505 terminal.

Be careful assigning the kmous capability. The ncurses wants to interpret it as KEY_MOUSE, for use by terminals and emulators like xterm that can return mouse-tracking information in the keyboard-input stream.

Different commercial ports of terminfo and curses support different subsets of the XSI Curses standard and (in some cases) different extension sets. Here is a summary, accurate as of October 1995:

SVR4, Solaris, ncurses -- These support all SVr4 capabilities.

SGI -- Supports the SVr4 set, adds one undocumented extended string capability (set_pglen).

SVr1, Ultrix -- These support a restricted subset of terminfo capabilities. The booleans end with xon_xoff; the numerics with width_status_line; and the strings with prtr_non.

HP/UX -- Supports the SVr1 subset, plus the SVr[234] numerics num_labels, label_height, label_width, plus function keys 11 through 63, plus plab_norm, label_on, and label_off, plus some incompatible extensions in the string table.

AIX -- Supports the SVr1 subset, plus function keys 11 through 63, plus a number of incompatible string table extensions.

OSF -- Supports both the SVr4 set and the AIX extensions.

FILES


/usr/share/terminfo/?/* files containing terminal descriptions

SEE ALSO


tic(1), infocmp(1), ncurses(3NCURSES), printf(3), term(5).

AUTHORS


Zeyd M. Ben-Halim, Eric S. Raymond, Thomas E. Dickey. Based on pcurses by Pavel Curtis.

openSUSE Logo

Contents