NAME


routes - configure the routing table

SYNOPSIS


/etc/sysconfig/network/routes /etc/sysconfig/network/ifroute-*

DESCRIPTION


The files /etc/sysconfig/network/routes and /etc/sysconfig/network/ifroute-config are parsed by the script /etc/sysconfig/network/scripts/ifup-route which sets up routing for an interface/configuration. ifup-route is used by /sbin/ifup, which is the command line user interface for setting up network interfaces.

/etc/sysconfig/network/routes is used for every interface while /etc/sysconfig/network/ifroute-config is used only for the network interface configuration stored in /etc/sysconfig/network/ifcfg-config, that means only for a certain interface. (See a discussion of the notions configuration, interface and device in ifup(8).)

At boot time /etc/init.d/network calls ifup for every existing configuration and uses ifup-route directly to set up special routes which do not belong to a certain interface.

The current routes can be seen by issuing:

/sbin/ip route list

which will give the current routing table.

Syntax


The files /etc/sysconfig/network/routes and /etc/sysconfig/network/ifroute-config use the same syntax. The only difference is the interpretation of an empty interface field. See 4th column below.

Lines beginning with # and blank lines are ignored. There are 5 columns with special meaning. Write a dash "-" if you want to omit an entry for a field. If all following fields in the line are empty too, you can even omit the dash.

The first column gives the destination, written as the IP-address of a host or a network. The heading default indicates that the route is the default gateway. Do not use 0.0.0.0 for this purpose. A prefix-length can be used; e.g., 10.10.0.0/16 is valid.

The second column contains the gateway. Write here the regular IP-address of a host which routes the packets to a remote host or remote network. You can omit this information for rejecting routes.

The third column gives the netmask for a remote host or remote network behind a gateway. For the default route or if you were using a prefix-length in the first column, you can omit it.

The fourth column gives the name of the interface of the local networks (lo, eth0, eth1, isdn0, ppp0, dummy0, ...).

If you leave this field empty the result depends on the file you are using. In /etc/sysconfig/network/routes the field is interpreted as no interface information available. That is sufficient for the most routes you may set up, but if you have multiple interfaces this route is set up with every single interface you activate. This may lead to error messages in the syslog. If you see such an error message which tells you "... this needs NOT to be AN ERROR" then check if you wrote the wrong ip addresses or if it occurs because it’s being set up with the wrong interface.

In the latter case you may want to use /etc/sysconfig/network/ifroute-config instead. Here an empty interface field is always replaced with the interface name that is currently being activated. This makes sense because this file is only used for one configuration (for one interface). This is even necessary if you use several hot-pluggable devices, because you cannot know the name of the interface that is used with a configuration for a certain device before.

The fifth column can be used to specify the type of a route:
unicast The route entry describes real paths to the destinations covered by the route prefix.
local The destinations are assigned to this host. The packets are looped back and delivered locally.
broadcast The destinations are broadcast addresses. The packets are sent as link broadcasts.
multicast A special type used for multicast routing. It is not present in normal routing tables.
throw A special control route used together with policy rules. If such a route is selected, lookup in this table is terminated pretending that no route was found. Without policy routing it is equivalent to the absence of the route in the routing table. The packets are dropped and the ICMP message net unreachable is generated. The local senders get an ENETUNREACH error.
unreachable These destinations are unreachable. Packets are discarded silently. The local senders get an EINVAL error.
prohibit These destinations are unreachable. Packets are discarded and the ICMP message communication administratively prohibited is generated. The local senders get an EACCES error.
blackhole These destinations are unreachable. Packets are discarded silently. The local senders get an EINVAL error.
nat A special NAT route. Destinations covered by the prefix are considered to be dummy (or external) addresses which require translation to real (or internal) ones before forwarding. The addresses to translate to are selected with attribute ’via’.
Any remaining columns, if given, are appended to the route command. This makes it possible to pass special options for this route. Columns which are not needed should contain a minus sign ( - ) to ensure that the parser correctly interprets the command.

EXAMPLES


An example with common network interfaces and some static routes:

# Destination Dummy/Gateway Netmask Device # 127.0.0.0 0.0.0.0 255.255.255.0 lo 204.127.235.0 0.0.0.0 255.255.255.0 eth0 default 204.127.235.41 0.0.0.0 eth0 207.68.156.51 207.68.145.45 255.255.255.255 eth1 192.168.0.0 207.68.156.51 255.255.0.0 eth1

An example for routing entries for synchronous ppp over a ISDN connection.

# Destination Dummy/Gateway Netmask Device # 127.0.0.0 0.0.0.0 255.255.255.0 lo 193.102.150.13 0.0.0.0 255.255.255.255 ippp0 default 193.102.150.13 0.0.0.0 ippp0

NOTES


SuSE Linux >= 8.0 uses the ip command from the iproute2 package to setup the network and routes. Please see the documentation distributed with this package for more information.

FILES


/etc/sysconfig/network/routes
/etc/sysconfig/network/ifroute-config

AUTHOR


Michal Svec <msvec@suse.cz> Christian Zoz <zoz@suse.de> Mads Martin Joergensen <mmj@suse.de>

Thanks to Werner Fink <werner@suse.de> for the old route.conf(5). Parts of the ip reference by Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> were also used.

SEE ALSO


init.d(7), init(8), inittab(5), the documentation for the iproute2 package and the SuSE Linux handbook, chapter The SuSE boot concept.

openSUSE Logo

Contents