NAME
spu_run - execute an SPU context
SYNOPSIS
#include <sys/spu.h>
int spu_run(int fd, unsigned int *npc
", unsigned int *" event ");"
DESCRIPTION
The spu_run() system call is used on PowerPC machines that implement the Cell Broadband Engine Architecture in order to access Synergistic Processor Units (SPUs). The fd argument is a file descriptor returned by spu_create(2) that refers to a specific SPU context. When the context gets scheduled to a physical SPU, it starts execution at the instruction pointer passed in npc.
Execution of SPU code happens synchronously, meaning that spu_run() blocks while the SPU is still running. If there is a need to execute SPU code in parallel with other code on either the main CPU or other SPUs, a new thread of execution must be created first (e.g., using pthread_create(3)).
When spu_run() returns, the current value of the SPU program counter is written to npc, so successive calls to spu_run() can use the same npc pointer.
The event argument provides a buffer for an extended status code. If the SPU context was created with the SPU_CREATE_EVENTS_ENABLED flag, then this buffer is populated by the Linux kernel before spu_run() returns.
The status code may be one (or more) of the following constants:
| SPE_EVENT_DMA_ALIGNMENT | |
| A DMA alignment error occurred. | |
| SPE_EVENT_INVALID_DMA | |
| An invalid MFC DMA command was attempted. | |
| SPE_EVENT_SPE_DATA_STORAGE | |
| A DMA storage error occurred. | |
| SPE_EVENT_SPE_ERROR | |
| An illegal instruction was executed. | |
RETURN VALUE
On success, spu_run() returns the value of the spu_status register. On error it returns -1 and sets errno to one of the error codes listed below.
The spu_status register value is a bit mask of status codes and optionally a 14-bit code returned from the stop-and-signal instruction on the SPU. The bit masks for the status codes are:
| 0x02 | SPU was stopped by a stop-and-signal instruction. |
| 0x04 | SPU was stopped by a halt instruction. |
| 0x08 | SPU is waiting for a channel. |
| 0x10 | SPU is in single-step mode. |
| 0x20 | SPU has tried to execute an invalid instruction. |
| 0x40 | SPU has tried to access an invalid channel. |
| 0x3fff0000 | |
| The bits masked with this value contain the code returned from a stop-and-signal instruction. These bits are only valid if the 0x02 bit is set. | |
ERRORS
| EBADF | fd is not a valid file descriptor. |
| EFAULT | npc is not a valid pointer, or event is non-NULL and an invalid pointer. |
| EINTR | A signal occurred while spu_run() was in progress; see signal(7). The npc value has been updated to the new program counter value if necessary. |
| EINVAL | fd is not a valid file descriptor returned from spu_create(2). |
| ENOMEM | There was not enough memory available to handle a page fault resulting from a Memory Flow Controller (MFC) direct memory access. |
| ENOSYS | The functionality is not provided by the current system, because either the hardware does not provide SPUs or the spufs module is not loaded. |
VERSIONS
The spu_run() system call was added to Linux in kernel 2.6.16.
CONFORMING TO
This call is Linux-specific and only implemented by the PowerPC architecture. Programs using this system call are not portable.
NOTES
Glibc does not provide a wrapper for this system call; call it using syscall(2). Note however, that spu_run() is meant to be used from libraries that implement a more abstract interface to SPUs, not to be used from regular applications. See http://www.bsc.es/projects/deepcomputing/linuxoncell/ for the recommended libraries.
EXAMPLE
The following is an example of running a simple, one-instruction SPU program with the spu_run() system call.
#include <stdlib.h>
#include <stdint.h>
#include <unistd.h>
#include <stdio.h>
#include <sys/types.h>
#include <fcntl.h>
#define handle_error(msg) \
do { perror(msg); exit(EXIT_FAILURE); } while (0)
int main(void)
{
int context, fd, spu_status;
uint32_t instruction, npc;
context = spu_create("/spu/example-context", 0, 0755);
if (context == -1)
handle_error("spu_create");
/* write a 'stop 0x1234' instruction to the SPU's
* local store memory
*/
instruction = 0x00001234;
fd = open("/spu/example-context/mem", O_RDWR);
if (fd == -1)
handle_error("open");
write(fd, &instruction, sizeof(instruction));
/* set npc to the starting instruction address of the
* SPU program. Since we wrote the instruction at the
* start of the mem file, the entry point will be 0x0
*/
npc = 0;
spu_status = spu_run(context, &npc, NULL);
if (spu_status == -1)
handle_error("open");
/* we should see a status code of 0x1234002:
* 0x00000002 (spu was stopped due to stop-and-signal)
* | 0x12340000 (the stop-and-signal code)
*/
printf("SPU Status: 0x%08x\n", spu_status);
exit(EXIT_SUCCESS);
}
SEE ALSO
close(2), spu_create(2), capabilities(7), spufs(7)
COLOPHON
This page is part of release 3.23 of the Linux man-pages project. A description of the project, and information about reporting bugs, can be found at http://www.kernel.org/doc/man-pages/.
